Profesionalūs betono priedų sprendimai, Betono putotojas, Superplastifikatorius, CLC blokų priedai, ir putojimo mašina
Pagrindinis pasirinkimas: Is 1000 kg/m³ putų betonas, tinkamas jums?
Putų betonas at 1000 kg/m³ yra konstrukcinis, lengvas lygintuvas. Tai nėra universalus sprendimas. This density offers a specific balance: enough strength for most residential and commercial floors, while providing insulation and weight savings that traditional sand-cement screeds cannot match. The decision hinges on your project’s specific needs for load, terminis pasirodymas, and subfloor condition. If you need a fast-drying, insulating layer that reduces dead load, this is your material. If you need extreme point load resistance or are working on a perfectly sound, non-porous substrate, look elsewhere.
Foamed Concrete vs. The Competition: Aiškus palyginimas
Choosing a floor levelling method is a technical decision. Relying on habit is expensive. The table below provides a direct, objective comparison based on core performance criteria for renovation and new construction.
| Criteria | Foamed Concrete (~1000 kg/m³) | Traditional Cement-Sand Screed (2000+ kg/m³) | Self-Levelling Compound (SLU) |
|---|---|---|---|
| Primary Strength | Compressive: 5-10 MPa. Good for distributed loads. | Compressive: 15-25 MPa+. Excellent for high point loads. | Compressive: 15-30 MPa. High early strength. |
| Key Advantage | Lightweight, superb thermal/acoustic insulation, flowable. | High compressive strength, low material cost, familiar. | Rapid setting, very thin applications, ultra-smooth finish. |
| Fatal Flaw | Lower tensile strength. Requires a stable, bonded substrate. | Very heavy, prone to shrinkage cracks, poor insulation. | Expensive at thickness >25mm, can be brittle. |
| Ideal Application | Leveling over weak substrates, insulating toppings, radiant heat systems, refurbishment. | Ground floors on compacted hardcore, heavy-duty industrial. | Final surface levelling over a solid base, under thin vinyl or carpet. |
| Drying/Curing Time | ~1 day/cm thickness for walking. Full cure/c drying: 4-6 weeks. | ~1-2 days/cm for walking. Full drying: 1 day/mm (long). | Walkable in 4-6 valandų. Ready for flooring in 24-72 valandų. |
| Installation Skill | Moderate-High. Requires pump, precise mix control, and proper priming. | Low-Moderate. Labor-intensive, skill-dependent for flatness. | Low. Poured and spread, but sensitive to substrate prep. |
The Niche Where Foamed Concrete Dominates
The data shows a clear winner for specific scenarios. A 2023 report from the International Lightweight Concrete Association notes a 40% increase in use of 1000-1200 kg/m³ mixes for refurbishment, citing weight and insulation as the dual drivers. As expert installer Marco Rossi states: “On old timber joist floors or above occupied apartments, foam concrete is the only responsible choice. You get a level, insulated floor without overloading the structure. Nothing else does both.” Its air-entrained structure provides a thermal conductivity (k vertė) aplinkui 0.2-0.3 W/mK, outperforming traditional screed by over 50%. This makes it a superior choice when levelling a floor is also your chance to improve building energy efficiency.
Kad tai veiktų: Installation & Long-Term Performance
Success with foamed betono is procedural. Ignore preparation at your peril.
Non-Negotiable Subfloor Preparation
The substrate must be sound, švarus, and primed for adhesion. This is not a decorative topping; it is a structural layer. Key steps:
- Assess Structural Integrity: The subfloor must be rigid. Fix any loose boards or cracks in a concrete base.
- Clean and Vacuum: Remove all dust, tepalas, and laitance. The primer must bond to the substrate, not the dirt.
- Apply a Bonding Primer: Use a slurry primer specified for lightweight concrete. This prevents the porous foam concrete from sucking moisture from the mix and de-bonding. This step is critical and often skipped.
- Install Perimeter Insulation Strip: This decouples the screed from walls, accommodating thermal movement and preventing crack transmission.
The Pour and The Cure
Placement is typically via a hose from a specialist pump truck. The material flows easily but should not be over-worked. Aim for a thickness between 40mm and 100mm for levelling applications. Thinner sections risk fragility; thicker sections require professional thermal calculation. After pouring, it will set enough to walk on in 24-48 valandų. Tačiau, full stiprumo development and moisture reduction (drying) takes weeks. The common industry mistake is installing moisture-sensitive floor coverings like wood or vinyl too soon. Use a moisture meter. Wait until relative humidity in the screed is below 75% RH, or as specified by your flooring manufacturer. The closed-pore structure of good foamed concrete reduces shrinkage cracking, but proper curing-covering with polyethylene sheeting for 3-7 days-is essential to prevent surface craze cracking.
Solving the Leveling Problem
When your project profile matches the niche-lightweight, insulating, flowable leveling over a prepared substrate-the choice becomes obvious. The process starts with a precise site evaluation and material specification. For this, partnering with a supplier who provides technical mix design support is crucial. A quality-controlled pre-batched foamed concrete mix, delivered by a knowledgeable pump operator, turns a complex material into a simple, on-site solution. This ensures you achieve the designed density of 1000 kg/m³ and the corresponding performance for floor leveling, guaranteeing the insulation and load-bearing properties your project requires.
Suppiler
Esame pasaulinis lengvojo betono ir pažangių putplasčio sprendimų lyderis. Visame pasaulyje žinomas dėl savo įsipareigojimo tyrimams, naujovių, ir pritaikytą ekspertizę, Mes teikiame suprojektuotus putplasčio sprendimus nuo 2012 m. pradžios.
Galime tiekti aukštos kokybės betono priedų ir putų betono gaminius visame pasaulyje.
Įmonėje veikia profesionalus techninis skyrius ir kokybės priežiūros skyrius, gerai įrengta laboratorija, ir įrengta pažangi testavimo įranga ir klientų aptarnavimo centras po pardavimo.
Jei jus domina, nedvejodami susisiekite su mumis.